cstaqdb@warwick.ac.uk (Tom Hughes) (06/19/91)
Can someone with access to some beeb manuals please post the details
for configuring the baud rate and data transfer info on the Master, as
I don't have my manuals here.
The items in question are the *CONFIGURE BAUD and *CONFIGURE DATA
values. These are the same as for *FX's 8 and 9 (??) on the beeb.
Thanks for any help, Tom.
============================================================================
Tom Hughes, CS1
thughes@uk.ac.warwick.cs Room 112 Compton Hall
cstaqdb@uk.ac.warwick.cu Westwood
University of Warwick
(0203) 523523 X2927 Coventry CV4 8EE
============================================================================rhodar@sideways.gen.nz (David Salmon) (06/21/91)
cstaqdb@warwick.ac.uk (Tom Hughes) writes: > Can someone with access to some beeb manuals please post the details > for configuring the baud rate and data transfer info on the Master, as > I don't have my manuals here. > > The items in question are the *CONFIGURE BAUD and *CONFIGURE DATA > values. These are the same as for *FX's 8 and 9 (??) on the beeb. > The following is taken from the Reference Manual Part One: To configure the baud rate is *configure baud <0 - 8> 0 = 9600 baud 1 = 75 baud 2 = 150 baud 3 = 300 baud 4 = 1200 baud 5 = 2400 baud 6 = 4800 baud 7 = 9600 baud and 8 = 19200 baud To configure baud is just *configure data <0 - 7> where: 0 = 7E2 1 = 7O2 2 = 7E1 3 = 7O1 4 = 8N2 5 = 8N1 6 = 8E1 7 = 8O1 Hope that helps. ------------------------------------------------------------------------ Rhodar@Tornado.welly.gen.NZ or Rhodar@Sideways.welly.gen.NZ Yad ho! Groja UL! *-}-----
hoskinsa@prlhp1.prl.philips.co.uk (hoskinsa) (06/21/91)
In article <+MX{MF-@warwick.ac.uk> cstaqdb@warwick.ac.uk (Tom Hughes) writes: >Can someone with access to some beeb manuals please post the details >for configuring the baud rate and data transfer info on the Master, as >I don't have my manuals here. > >The items in question are the *CONFIGURE BAUD and *CONFIGURE DATA >values. These are the same as for *FX's 8 and 9 (??) on the beeb. > >Thanks for any help, Tom. Here are the numbers for *FX7,X (receive rate) and *FX8,X (transmit rate): X=1 : 75 baud After Call: 2 : 150 baud A is preserved. 3 : 300 baud X & Y contain old ULA register contents. 4 : 1200 baud C is undefined. 5 : 2400 baud 6 : 4800 baud 7 : 9600 baud 8 : 19200 baud Mail me if you want the info to set up data format (# of start/stop/data bits) and I'll see if I can persuade my OCR to read the manual (too much to type :-). Asher +----------------------------------------------------------------+ | And then a little pink swan flew slowly past, the marmalade | | curdled, and everyone in Legoland went home for a concrete | | penguin. "Don't forget to write", shouted Sniffy, but the cake | | had already been eaten. - BSH | +-----------------------------------------------+----------------+-----------+ | hoskinsa@prl.philips.co.uk | +----------------------------+