dwp@mtune.ATT.COM (David Preisler) (10/25/89)
On a 3b2 700 under sVr3 I've got GNU Emacs 18.54 built [ HAVE_PTY defined ],
but I find that it does not work properly through a DataKit VC. I do find
however, that when run through a direct port it appears to work properly.
Symptoms: The screen opens up correctly, but typed chars do not appear on
the screen. Ctrl chars are also generally ignored. Emacs will beep at ^g
and ^z, and occasionally it will produce the unsupported operation message
( autosave, abort- core dump ).
Does anyone know what is going on or [ even ] how to debug the problem.
thanks again,
David William Preisler
System Administrator
AT&T Bell Laboratories Email: att!mtune!dwp
200 Laurel Avenue
Middletown, NJ 07748 Phone: (201) 957-2594psm@cbnewse.ATT.COM (Steve Murphy) (10/25/89)
In article <8124@mtune.ATT.COM> dwp@mtune.ATT.COM (David Preisler) writes:
=> On a 3b2 700 under sVr3 I've got GNU Emacs 18.54 built [ HAVE_PTY defined ],
=> but I find that it does not work properly through a DataKit VC. I do find
=> however, that when run through a direct port it appears to work properly.
=>
=> Symptoms: The screen opens up correctly, but typed chars do not appear on
=> the screen. Ctrl chars are also generally ignored. Emacs will beep at ^g
=> and ^z, and occasionally it will produce the unsupported operation message
=> ( autosave, abort- core dump ).
=>
=> Does anyone know what is going on or [ even ] how to debug the problem.
I had the same problem with GNU Emacs over STARLAN. One question, are the
devices DataKit use for remote logins streamio devices? If they are you're
out of luck. When I found out that STARLAN devices were streamio devices, I
was annoyed. When I found out that streamio devices do not behave like
tty's, I was ticked. GNU Emacs makes certain ioctl calls that will fail on
streamio devices. I could'nt find a solution to my problem.
--
===============================================================================
Steve Murphy |"My work is visionary or imaginative. That which can
1(312)510-4678 | be made explicit to the idiot is not worth my care..."
att!nwgpa!toolserv!psm | - William Blake, Apocalypse by Imaginationdmiller%cs2.cs.WSU.EDU@CS2.CS.WSU.EDU (10/26/89)
>>In article <8124@mtune.ATT.COM> dwp@mtune.ATT.COM (David Preisler) writes: >>=> On a 3b2 700 under sVr3 I've got GNU Emacs 18.54 built [ HAVE_PTY defined [...] >>=> Symptoms: The screen opens up correctly, but typed chars do not appear on >>=> the screen. Ctrl chars are also generally ignored. Emacs will beep at ^g >>=> and ^z, and occasionally it will produce the unsupported operation message [...] >>I had the same problem with GNU Emacs over STARLAN. One question, are the We are running GNU Emacs over STARLAN on a 3b2/400 with no problems. I did not do the installation, but lookin at the sources, I noticed that it is version 18.51 (last ChangeLog entry: Fri May 6 10:41:46 1988...). Has RMS made some sort of change since then that makes 3b2/STARLAN croak? If so, I would like to know before I attempt to upgrade :-) --DLM ********************************************************************** David L. Miller Internet: millerd@prime.tricity.wsu.edu (?) Systems Analyst or dmiller@cs2.cs.wsu.edu (reliable) WSU Tri-Cities 100 Sprout Rd. Voice: (509) 375-9245 or 375-3176 Richland, WA 99352 >>>>>>>>>>> Support the FSF <<<<<<<<<<<