cmv@ihuxz.ATT.COM (Craig Votava) (02/19/88)
Fri Feb 19 13:59:54 CST 1988 This proceedure has been confirmed. -- cmv Here is another repost that I promised on upgrading memory on the motherboard. Once again I want to say that I have not done this on my machine ... yet, maybe someone that has can confirm the proceedure?? /* Written 10:16 am Jul 13, 1987 by looney!cmv in ihlpm:unix-pc.general */ /* ---------- "7300 Motherboard upgrade proceedure" ---------- */ Here is an untested, unverified proceedure for upgrading the motherboard on a unix-pc. Do not follow this proceedure unless you KNOW WHAT YOU ARE DOING! If you trash your motherboard, only YOU can be responsible for the damage! The text of this proceedure was, at one time, in an official document, it has since been dropped. 256K BYTE RAM CHIP UPGRADE Memory on the processor board and on the memory expansion board may be expanded from 512K bytes to 2M bytes. This is accomplished by installing 256K byte RAM chips in place of the original 64K byte RAM chips. UPGRADING THE PROCESSOR BOARD - There are seventy-two MB8264 chips located on the processor board. These are 150nsec, 64K byte RAM chips manufactured by Fujitsu (the RAM chips used in future machines may be provided by another vendor due to the laws of supply and demand). These chips are illustrated in the schematics on sheets 19 thru 22. These chips will have to be removed and replaced with the appropriate 256K byte RAM chips (for example, MB81256-15). - After the 256K byte chips have been installed, memory size has quadrupled. Two more address bits will be required to access this extra memory, therefore another address MUX is needed. (sheet 18) A 74F258 Multiplexor chip must be installed at board location 13B. - Jumper JR1 (sheet 18) is located at the front of the processor board, to the immediate left of the chip in position 12A. When 64K byte RAM chips are being used, it is jumpered E2-E3. With the installation of 256K byte RAM chips the E2-E3 connection should be opened and re-jumpered E1-E2. HERE WE GO AGAIN WITH THE WARNINGS... I should warn you that I have not tried this proceedure yet, so I cannot vouch for the correctness. It's possible that I will be trying this out on my motherboard (512K) sometime in the future, but I already have a 0K RS-232 expansion board to upgrade first. So I really can't be responsible for anything that may happen to your machine from following this proceedure. I really can't help you more than to say GOOD LUCK! Craig Votava AT&T Bell Labs, Naperville IL ihnp4!looney!cmv /* End of text from ihlpm:unix-pc.general */
hoffman@pitt.UUCP (Bob Hoffman) (02/25/88)
In article <2634@ihuxz.ATT.COM> cmv@ihuxz.UUCP (Craig Votava) writes: >Fri Feb 19 13:59:54 CST 1988 >This proceedure has been confirmed. -- cmv > >Here is another repost that I promised on upgrading memory on the motherboard. >Once again I want to say that I have not done this on my machine ... yet, >maybe someone that has can confirm the proceedure?? I confirmed this privately to Craig, but I think I should tell the rest of the net as well. I have done this upgrade myself and it works. Do exactly what Craig says and you will have a working 2mb motherboard. For desoldering, I used an Ungar 4000 desoldering station. I also used Augat machined-pin gold-plated sockets. Total time to do the upgrade was approximately eight hours. It's quite fatiguing to desolder 72 16-pin chips, so I spread the work out over three nights. I did this upgrade in July 1987 and it has been working without a hitch ever since. ---Bob. -- Bob Hoffman, N3CVL {allegra, bellcore, cadre, idis, psuvax1}!pitt!hoffman Pitt Computer Science hoffman%pitt@relay.cs.net