henry (11/30/82)
The manual page Bob Brown submitted actually contained several errors
and omissions, perhaps the result of working from vcat rather than
from a CAT manual. The following description of the format of troff
phototypesetter codes is essentially a tidied-up version of the CAT
hardware documentation, verified by experience with a real CAT:
-----
.TH CAT 5 local writeup
.DA 4 April 1981
.SH NAME
cat \- C/A/T phototypesetter code
.SH DESCRIPTION
The Graphic Systems C/A/T phototypesetter is driven by sending it a
sequence of one-byte codes
which specify characters, fonts, sizes, and other control information.
.PP
The C/A/T's basic unit of length is 1/432 of an inch (6 units to a
typesetter's ``point'').
The quantum of horizontal motion is one unit.
The quantum of vertical motion is three units (1/144 of an inch, 1/2 point).
.PP
The top two bits of the code classify it as one of three major
types:
an \fIescape\fR code (top bit 1),
a \fIflash\fR code (top bits 00),
or a control code (top bits 01).
A code of all zeros is ignored; a code of all ones is illegal.
.PP
A flash code specifies flashing one of 63 characters, as given by the
remaining six bits.
Since this is not enough to specify all possible characters, or even
all characters in a single font \(em there are 108 per font \(em
various control codes (described later) select a font and either
the Lower or Upper half of the font.
The Lower half is the first 63 characters of the font; the Upper
half is the remaining 45.
A flash code of 46 or higher in the Upper half is illegal.
.PP
An escape code specifies horizontal motion.
The size of the motion, in horizontal quanta, is the one's-complement
of the low seven bits of the code.
The direction of the motion is set by control codes.
Hitting the right or left margin limit switch is illegal and will
cause the machine to stop.
The machine starts out, after initialization, hard against the left
margin limit switch; an initial escape of 16 units \fImust\fR
be given before starting work, and the position after this motion
should be the limit of all future leftward motions.
>From this point, the distance to the right margin limit switch
is about 7.5 inches.
.PP
A code with the top three bits 011 is a \fIlead\fR code,
specifying vertical motion.
The remaining five bits are the one's-complement of the size of
the motion, in vertical quanta.
The direction of motion is set by control codes.
The amount of vertical motion is, in principle, limited only by
running off the paper in the upward direction and by the limited
capacity of the output cartridge in the downward direction.
.PP
A code with the top four bits 0101 is a size-change code, which
specifies movement of the lens turret and the doubler lens to
change point size.
These codes are as follows:
.PP
.RS
.nf
.ta 2c
Size Code
6 0101\|1000
7 0101\|0000
8 0101\|0001
9 0101\|0111
10 0101\|0010
11 0101\|0011
12 0101\|0100
14 0101\|0101
16 0101\|1001
18 0101\|0110
20 0101\|1010
22 0101\|1011
24 0101\|1100
28 0101\|1101
36 0101\|1110
.DT
.fi
.RE
.PP
Size changes involving the doubler lens alter the horizontal position.
Changes from single to double sizes should be followed by a forward
escape of 55 quanta; changes from double to single sizes should be
followed by a reverse escape of 55 quanta.
The single sizes are 6, 7, 8, 9, 10, 11, 12, 14, and 18;
the double sizes are 16, 20, 22, 24, 28, and 36.
.PP
The control codes with the top four bits 0100 specify miscellaneous
control codes, not all of which have valid meanings.
They are:
.PP
.RS
.ta 6c
.nf
initialize 0100\|0000
stop 0100\|1001
upper rail 0100\|0010
lower rail 0100\|0001
upper mag 0100\|0011
lower mag 0100\|0100
tilt up 0100\|1110
tilt down 0100\|1111
upper font half 0100\|0110
lower font half 0100\|0101
escape forward 0100\|0111
escape backward 0100\|1000
lead forward 0100\|1010
lead backward 0100\|1100
.fi
.DT
.RE
.PP
The \fIinitialize\fR code causes leftward motion to the left margin limit
switch,
and sets the following modes:
escape forward, lead forward, lower font half,
lower rail, lower mag, tilt down.
Note that the left margin limit switch does not define a precise
position, and hence reinitializing the machine
will destroy precise left-margin alignment.
.PP
The \fIstop\fR code stops the machine, which must be manually
restarted (normally after changing output cartridges);
this code should be used only at the end of a run.
.PP
Fonts are selected by the combination of \fIrail\fR, \fImag\fR, and \fItilt\fR.
The tilt codes do not exist on the 4-font C/A/T; this is the only user-visible
difference between the 4-font and 8-font machines.
The correspondence between rail/mag/tilt and font number is as follows:
.PP
.RS
.nf
.ta 2c 4c 6c 8c
rail mag tilt 4font 8font
lower lower up 1 1
lower lower down 1 2
upper lower up 2 3
upper lower down 2 4
lower upper up 3 5
lower upper down 3 6
upper upper up 4 7
upper upper down 4 8
.DT
.fi
.RE
.PP
A complete C/A/T file should begin with an \fIinitialize\fR code following
by an \fIescape\fR-16 code,
and should end with 14 inches of trailer and a \fIstop\fR code.
.SH HISTORY
This manual page written at U of T by Henry Spencer.
.SH BUGS
The documentation and the hardware disagree on the initial tilt setting;
the above describes the hardware.
.PP
It's not the fastest or most modern typesetter.
-----