michaele@vice.ICO.TEK.COM (Michael Enkelis) (02/28/90)
I am trying to configure a UDA-50 + RA80 disk drive into my
VAX 11/730 system. Everything seems ok on boot up,
but within 24 hours i get the following messages and the system is hung.
Feb 23 10:18
uda0: soft error, SDI error, unit 0, event 053, hdr 0x0
0x13 0x4 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
uda0: soft error, SDI error, unit 0, event 0113, hdr 0x0
0x13 0x4 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
uda0: soft error, SDI error, unit 0, event 0113, hdr 0x0
0x13 0x4 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
uda0: hard error
uda0: hard error, SDI error, unit 0, event 0113, hdr 0x0
0x13 0x4 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
uda0: soft error, SDI error, unit 0, event 0113, hdr 0x0
0x13 0x4 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
uda0: soft error, SDI error, unit 0, event 0113, hdr 0x0
0x13 0x4 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
uda0: hard error
uda0: hard error, SDI error, unit 0, event 0113, hdr 0x0
0x13 0x4 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
ra0c: hard error sn64 OFFLINE
My system consistes of:
4.3 BSD UNIX #5: Fri Feb 16 23:27:28 PST 1990
root@enky:/sys/VAX730
real mem = 4194304
avail mem = 3389440
using 153 buffers containing 314368 bytes of memory
mcr0 at tr0
uba0 at tr3
idc0 at uba0 csr 175606 vec 250, ipl 15
rb0 at idc0 slave 0
rb1 at idc0 slave 1
uda0 at uba0 csr 172150 vec 774, ipl 15 <<-- in exp box.
ra0 at uda0 slave 0
zs0 at uba0 csr 17250 vec 224, ipl 15 <<-- in exp box.
ts0 at zs0 slave 0
dmf0: printer synch asynch.
dmf0 at uba0 csr 160340 vec 734, ipl 15
vp reset vec from 200 to 174 <<-- in exp box.
vp0 at uba0 csr 177510 vec 174, ipl 14
Any ideas on jumper setting on UDA? or card placement in exp box.
--
_ _ _ __
' ) ) ) / /) / ` / /) Michael Enkelis
/ / / o _. /_ __. _ // /-- __ /_ _ // o _ tektronix!vice!michaele
/ ' (_(_(__/ /_(_(_(<_(/_ (___, /) )_/ <_(<_(/_(_/_)_ (503) 627-4099dave@wizard.UUCP (Dave Wallace) (03/02/90)
In article <4764@vice.ICO.TEK.COM>, michaele@vice.ICO.TEK.COM (Michael Enkelis) writes: > > I am trying to configure a UDA-50 + RA80 disk drive into my > VAX 11/730 system. Everything seems ok on boot up, > but within 24 hours i get the following messages and the system is hung. > > Feb 23 10:18 > uda0: soft error, SDI error, unit 0, event 053, hdr 0x0 > 0x13 0x4 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 We had a similar trouble here, only running System V R2.2 on a VAX 730. The problem was not with switch settings, but was a trouble with the physical drive. I think its call the maintenance folks time (sorry to say) > uda0 at uba0 csr 172150 vec 774, ipl 15 <<-- in exp box. This message is quite correct. There is only switch settings for the csr, not the vectore ( as in other old DEC products ). The csr HAS to be correct otherwise the system wouldn't even get this far, and the vector address is downloaded to the board. By the way, we retired the VAX 730. Dave Wallace
chris@mimsy.umd.edu (Chris Torek) (03/07/90)
In article <4764@vice.ICO.TEK.COM> michaele@vice.ICO.TEK.COM (Michael Enkelis) writes [edited to bare essentials]: >uda0: soft error, SDI error, unit 0, event 053, hdr 0x0 >uda0: soft error, SDI error, unit 0, event 0113, hdr 0x0 >uda0: hard error, SDI error, unit 0, event 0113, hdr 0x0 These are, in order: sdi command timeout drive error (soft) ctlr detected protocol drive error (soft) ctlr detected protocol drive error (hard) This indicates a problem in the controller (uda50 or equivalent), drive, or cabling between the two. >4.3 BSD UNIX #5: Fri Feb 16 23:27:28 PST 1990 Convert to 4.3BSD-tahoe; you will get a much better UDA/RA driver. -- In-Real-Life: Chris Torek, Univ of MD Comp Sci Dept (+1 301 454 7163) Domain: chris@cs.umd.edu Path: uunet!mimsy!chris