dhc@a.UUCP (Dave Carter) (01/13/88)
>
anyone know the best (cheapest) place to get an hp laserjet II (mail
order or otherwise) (or anybody selling one?)
also, anybody have any problems with these printers? all i've heard
about them so far has been good.
please send e-mail, and i'll summarize, if interesting.
- dave
dhc@lanl.govdehart@tl-vaxa.UUCP (Ed DeHart) (01/27/88)
> > anyone know the best (cheapest) place to get an hp laserjet II (mail > order or otherwise) (or anybody selling one?) D & K Electronics 412-422-3733 > > also, anybody have any problems with these printers? all i've heard > about them so far has been good. > We have two of them. One connected to a Microvax and the other to an AT clone. I just upgraded the RAM from 512K to 4.5 megabytes on each unit. All is well and we are happy. Ed DeHart
pls@sortac.UUCP (Pat Sullivan) (01/28/88)
In article <243@tl-vaxa.UUCP> dehart@tl-vaxa.UUCP (Ed DeHart) writes: > . . . I just upgraded the RAM from 512K to 4.5 megabytes on each >unit. All is well and we are happy. > Ed DeHart We would like to upgrade the memory on ours, but the best price we found is a bit steep (teens of hundreds). How much did your upgrade cost? Is it a complete kit (i.e., can a typical knuckle-dragger do it)? Where did you buy it? I know - I ask too many questions, but thanks in advance for whatever you can answer. =================================================================== Pat Sullivan - {gatech|akgua|ihnp4}!sortac!pls - voice 404-257-7382
pavlov@hscfvax.harvard.edu (G.Pavlov) (01/29/88)
In article <240@sortac.UUCP>, pls@sortac.UUCP (Pat Sullivan) writes: > In article <243@tl-vaxa.UUCP> dehart@tl-vaxa.UUCP (Ed DeHart) writes: > > . . . I just upgraded the RAM from 512K to 4.5 megabytes on each unit. > > Ed DeHart > > We would like to upgrade the memory on ours, but the best price we found > is a bit steep (teens of hundreds). > Have you considered a 2-meg upgrade (resulting in total of 2.5 meg) ? Seems that this should be more than sufficient for all but the most "discer- ning" applications - greg pavlov, fstrf, amherst, ny
dehart@darth.UUCP (Ed DeHart) (02/11/88)
> In article <240@sortac.UUCP>, pls@sortac.UUCP (Pat Sullivan) writes: > > In article <243@tl-vaxa.UUCP> dehart@tl-vaxa.UUCP (Ed DeHart) writes: > > > . . . I just upgraded the RAM from 512K to 4.5 megabytes on each unit. > > > Ed DeHart > > > > We would like to upgrade the memory on ours, but the best price we found > > is a bit steep (teens of hundreds). > > > Have you considered a 2-meg upgrade (resulting in total of 2.5 meg) ? > Seems that this should be more than sufficient for all but the most "discer- > ning" applications - > > greg pavlov, fstrf, amherst, ny We purchased the HP Laserjet series II and RAM upgrade from: D & K Electronics, Pittsburgh, Pa. (412) 422-3733 The RAM upgrade was around $1200.00 for the four meg board. Since we were planning to print a lot of graphics we went for the full RAM upgrade. It was very easy to install. Anyone should be able to do the upgrade in a few minutes.