CSULLOGG@CRL.AECL.CA (04/15/91)
For about 2 months, I have been using the following assign.sys file with my TT and a PTC1426 colour monitor. When I switched to a TTM195 mono monitor, I could no longer boot my system with GDOS (a screen message would say that GDOS 1.1 was resident but 2 bombs would appear during the desk accessory loading step). I tried rewritting the assign.sys file dozens of ways (see the example at the end of this posting) but the system still crashes. What the heck do I have to have in my assign.sys file to get GDOS to load properly? For netland information, YES, all the drivers and fonts ARE in the path specified by the path statement! The fonts (except metafonts) and drivers are from my Timeworks DTP software. The metafonts are from my LDW software. Crashes occur even when I strip all AUTO programs out except GDOS and when all accessories are inactivated. Crashes occur whether or not NEOLOAD is run from the AUTO folder. If I do run NEOLOAD, when the system crashes I get the following diagnostic page: A bus error occurred (2 bombs) d0:00000000 a0:21FC0000 d1:00058E62 a1:00E37F00 d2:00000000 a2:0005A0F0 d3:00000001 a3:000031A2 d4:00000000 a4:000059E4 d5:00000000 a5:00E00EF2 d6:00000000 a6:0000BC4A d7:00000000 a7:0000BBE2 ssp:0000BBE2 usp:0003DE2E instr:FFFFB008 sr: 16EE = {t:0 s:0 interrupt:110 x:0 n:1 z:1 v:1 c:0} pc:076D66F2 Does anyone know what to do??????? I need an answer a.s.a.p. because U have drawings to complete with EASYDRAW. == the following is the assign.sys that worked with the PTC1426 ===== ;HPLJ II @ 300dpi + LDW Metafonts path = c:\gemsys 01p screen.sys ; DEFAULT 02p screen.sys ; LOW RES 03p screen.sys ; MED RES 04p screen.sys ; HI RES shss03as.fnt shss05as.fnt shss06as.fnt shss07as.fnt shss10as.fnt shss12as.fnt shss14as.fnt shss18as.fnt shss24as.fnt shss36as.fnt shtr07as.fnt shtr10as.fnt shtr14as.fnt shtr18as.fnt shtr36as.fnt shrk10as.fnt shrk18as.fnt shrk36as.fnt shra09as.fnt shra18as.fnt shra36as.fnt shdl10c.fnt shdl18c.fnt shdl36c.fnt shma09as.fnt shma18as.fnt shma36as.fnt shdb07.fnt shdb10.fnt shdb14.fnt shdb18.fnt shdb36.fnt 05p screen.sys 06p screen.sys shss03as.fnt shss05as.fnt shss06as.fnt shss07as.fnt shss10as.fnt shss12as.fnt shss14as.fnt shss18as.fnt shss24as.fnt shss36as.fnt shtr07as.fnt shtr10as.fnt shtr14as.fnt shtr18as.fnt shtr36as.fnt shrk10as.fnt shrk18as.fnt shrk36as.fnt shra09as.fnt shra18as.fnt shra36as.fnt shdl10c.fnt shdl18c.fnt shdl36c.fnt shma09as.fnt shma18as.fnt shma36as.fnt shdb07.fnt shdb10.fnt shdb14.fnt shdb18.fnt shdb36.fnt 07p screen.sys shss03as.fnt shss05as.fnt shss06as.fnt shss07as.fnt shss10as.fnt shss12as.fnt shss14as.fnt shss18as.fnt shss24as.fnt shss36as.fnt shtr07as.fnt shtr10as.fnt shtr14as.fnt shtr18as.fnt shtr36as.fnt shrk10as.fnt shrk18as.fnt shrk36as.fnt shra09as.fnt shra18as.fnt shra36as.fnt shdl18c.fnt shdl36c.fnt shma09as.fnt shma18as.fnt shma36as.fnt shdb07.fnt shdb10.fnt shdb14.fnt shdb18.fnt shdb36.fnt 21 HPLJII.sys ;Printer is HP Laserjet 2 @300dpi lpss06as.fnt lpss08as.fnt lpss10as.fnt lpss12as.fnt lpss14as.fnt lpss18as.fnt lptr06as.fnt lptr08as.fnt lptr10as.fnt lptr12as.fnt lptr14as.fnt lptr18as.fnt lprk10as.fnt lprk18as.fnt lpra09as.fnt lpra18as.fnt lpdl10c.fnt lpdl18c.fnt lpma12as.fnt lpma18as.fnt lpdb07.fnt lpdb10.fnt lpdb14.fnt lpdb18.fnt 31 meta.sys ;metafonts for metafiles attr10mf.fnt attr12mf.fnt attr18mf.fnt attr24mf.fnt attp10mf.fnt atss10mf.fnt atss12mf.fnt atss18mf.fnt atss24mf.fnt ======================================================================== The next file is my last attempt at rewriting the assign.sys file. It, like all the other versions, did not work. HELP!!!!! ======================================================================== path = c:\gemsys.804 01p screen.sys 02p screen.sys 03p screen.sys 04p screen.sys ATTR10.FNT ATTR12.FNT ATTR18.FNT 05p screen.sys 06p screen.sys ATTR10.FNT ATTR12.FNT ATTR18.FNT 07p screen.sys ATTR10.FNT ATTR12.FNT ATTR18.FNT 21 slm804.sys ATTR10LS.FNT ATTR12LS.FNT ATTR18LS.FNT 31 meta.sys ATTR10MF.FNT ATTR12MF.FNT ATTR18MF.FNT